• Signs and Symptoms of Acute Overexposure: Eye, skin irritation. Inhalation of heated vapors may irritate the respiratory tract.
• Signs and Symptoms of Chronic overexposure: Prolonged inhalation of concentrated.heated vapors may cause damage to the kidneys. Reddening and swelling of affected area with possile itching, burning or other discomfort.
• Medical Conditions Generally Aggravated by Exposure: Existing cuts, rashes, allergies, or other sensitive areas.
• Ingestion: Ingestion may result in abdominal pain, nausea, and vomiting.

• Inhalation: Remove victim to fresh air
• Ingestion: Give victim water or milk to drink to dilute the product. Get medical advice..
• Skin Contact: Remove contaminated clothing and footwear. Wash skin with soap and water. Wash clothing before reuse.
• Eye Contact: Immediately flush eyes with water for 15 minutes. Get medical attention.
• Note to Physician: None

 Flash Point: > 200 degrees F (PMCC)

Flammability Limits: NDA

Autoignition temp: NDA

Fire Extinguishing Media: Any available extinguishing including water spray, carbon dioxide, dry chemical, Halon 1211

Special Fire-Fighting Information: Spilled chemical creates extremely slippery conditions, especially in contact with water. Use caution. Respiratory and eye protection are reqyired. Petroleum component is combustible, if separated from other ingredients. Vapors/fumes will ignite.

Unusual Fire and Explosion Hazards: Hydrocarbon components are combustible if separated from the emulsion.

• Ventilation System: Good general ventilation is advisable. Local exhaust desired.
• Personal Respirators (NIOSH Approved): None required for normal use and processes. if needed, use respirator to filter out mists/vapors.
• Skin Protection: Long sleeved clothing, impervious rubber or neoprene gloves and protective apron.
• Eye Protection: Safety glasses or goggles
• Other Control Measures: Minimize exposure in accordance with good hygiene practice. Avoid handling which would create large amounts of mists/vapors. Exxon Medical Research recommended inhalation TLV for CAS 64742-47-8 of 200 ppm.

• Appearance and Color: Milky-white emulsion.
• Odor: Mild petroleum and acrylate
• Solubility in Water: 0.5 - 1%
• Specific Gravity: 1.13
• Viscosity at 28 deg. C: < 4000 cps
• % volatile by volume @ 21C (70F): NDA
• Boiling Point: > 210 degrees F
• Melting Point: < 23 degrees F
• Freezing Point: - 15 degrees C
• Vapor Density (Air=1): > 1
• Vapor Pressure (mm Hg): 37
• Evaporation Rate (Bu. Acetate=1): < 1

• Stability: Product is stable.
• Hazardous Decomposition Products: None known
• Hazardous Polymerization: will not occur.
• Incompatibility: Strong oxidizers: liquid chlorine, concentrated oxygen, sodium hypochlorite, calcium hypochlorite
• Conditions to Avoid: Incompatible substances

• Toxicological Data:

RTECS: CAS 2607-38-3: MD0906000, WZ4725000; CAS 25085-02-3: 1011973HP; CAS 64642-47-8: OA5504000

Eye & skin irritant. May aggravate existing medical conditions, such as rashes, allergies or other sensitive areas. Symptoms may include reddening, swelling of effected areas with possible itching, burning or other discomfort.

• Carcinogenicity: Not listed by ACGIH, IARC, NIOSH, NTR, or OSHA

• Environmental Fate: CAS# 25085-02-3: Aquatic LC50, Ceriodaphnia dubia, 48 hours = 1.55 ppm/ Pimephales promeias, 48 hours = 12.0 ppm
  BOD (Biological Oxygen Demand) = 383,000 mg/L
  COD (Chemical Oxygen Demand) = 1.930,000 mg/L
• Environmental Toxicity: NDA
• Biodegradability: Laboratory studies indicate limited biodegradation with "non-acclimated sludge", based on component data, but cultures in Alken Clear-Flo 7004 are easily able to metabolize the nonylphenol sufactant and petroleum solvent in Alken Solutions A3050L.Products of biodegradation are less hazardous than original polymer ingredients.

• DOT Proper Shipping Name: Not regulated as hazardous by DOT or Canadian TDG
• DOT Hazard Class: None
• DOT Label: Class 60:(NMFC item #4612, LTL) "adhesives, adjuvents, spreaders, sliders, liquid, in pails or drums" Alken Solutions A3050L, anionic acrylamide polymer liquid
  

• TSCA: : (40CFR 710) All chemical ingredients are listed on the TSCA 8(b) inventory. None of the ingredients are on the Health and Safety Reporting List, are under Chemical Test rule, are listed under TSCA Section 12B, or have a SNUR under TSCA
  CERCLA Reportable Quantity: This product does NOT contain ingredients that have Reportable Quantity (RQ) requirements under US 40 CFR 117.302
• SARA TITLE III:

  Section 302/304 Extremely Hazardous Substances: None Section 311 Hazard Categorization: None Section 313 Toxic Chemicals: None

• Clean Water Act: None of the chemicals in this formula are listed as Priority Pollutants under CWA.
• Clean Air Act : Ingredients not listed as hazardous pollutants under CAA. This product does not contain any Class 1 or Class 2 ozone depletors, nor was it made with such chemicals.
• OSHA: None of the ingredients are considered Extremely Hazardous by OSHA.
• STATE RIGHT-TO-KNOW LAWS:. Ingredients not listed on California, Connecticut, Florida, Illinois, Louisiana, Massachusetts, New Jersey, New York, Pennsylvania, or Rhode Island.
• Not subject to California Proposition 65 labeling requirements
• Canadian WHMIS Classification: CAS 64742-47-8: B3. Combustible Liquid, but flash point of formulated product has a flash pint above flammable-combustible limit for Canada
• Canadian DSL: all ingredients listed and compliant
• Canada's Ingredient Disclosure List: Light hydrotreated kerosine solvent CAS# 64742-47-8, comprising 25% of this product IS listed on the CIDL, but other ingredients are "NOT CONTROLLED". This MSDS has been prepared according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.
• TDG Classification: Not regulated as hazardous by Canadian TDG.
• IHT Codes: 3906.90.5000
  

Reason for Revision: Routine review & revision

Alken-Murray Corporation provides the information contained herein in good faith, in compliance with the Occupational Safety and Health Act of 1970, but makes no representation as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Alken-Murray warrants that this product is of merchantable quality. The implied warranty of fitness for a particular purpose is limited to the extent the products are used for the purpose or uses described on the product's label or in any written instructions or materials distributed to the buyer by Alken-Murray and is hereby disclaimed should buyer use the products in a manner inconsistent with this uses or purposes described therein. In no event shall Alken-Murray be liable for any consequential, exemplary, or incidental damages incurred by buyer even if it has been advised of the possibility of such damages.