NFPA Hazard Ratings:

0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe

Emergency Overview: Organisms used are non-pathogenic, but can cause infection when in contact with open wounds. These organisms are susceptible to many commonly used antibiotics.

Potential Health Effects:

• Signs and Symptoms of Acute Overexposure: Eye, skin irritation
• Signs and Symptoms of Chronic overexposure: Dermatitis and skin sensitization
• Medical Conditions Generally Aggravated by Exposure: Allergies, dermatitis.
• Ingestion: No effect if ingested in small amounts. Relative to other materials, a single dose of this product is rarely toxic by ingestion. Irritation of the mouth, pharynx, esophagus and stomach can develop following ingestion.

• Inhalation: Remove victim to fresh air
• Ingestion: Give victim water or milk to drink to dilute the product. Get medical advice..
• Skin Contact: Remove contaminated clothing and footwear. Wash skin with soap and water. Wash clothing before reuse.
• Eye Contact: Immediately flush eyes with water for 15 minutes. Get medical attention.
• Note to Physician: If patient's immune system is compromised, request antibiotic sensitivity chart from Alken-Murray Corporation by e-mail: clearflo@shentel.net

 Flash Point: NA

Flammability Limits: NA

Autoignition temp: NA

Fire Extinguishing Media: Water spray, carbon dioxide, dry chemical

Special Fire-Fighting Information: None

Unusual Fire and Explosion Hazards: None

• Ventilation System: Good general ventilation is advisable
• Personal Respirators (NIOSH Approved): if needed, use respirator to screen out nuisance dust
• Skin Protection: Long sleeved clothing
• Eye Protection: Safety glasses if dust is raised
• Other Control Measures: Minimize exposure in accordance with good hygiene practice. Avoid handling which would create large amounts of dust.

• Appearance and Color: Free-flowing tan to brown powder.
• Odor: Yeast-like odor
• Solubility in Water: Moderate, contains viable bacteria
• Specific Gravity: NDA
• Bulk density: Approximately 0.66-0.77 gm/cm3
• pH: 6.5-8.5
• % volatile by volume @ 21C (70F): Nil
• Boiling Point: NA
• Melting Point: NA
• Vapor Density (Air=1): NA
• Vapor Pressure (mm Hg): NA
• Evaporation Rate (Bu. Acetate=1): NA

• Stability: Product is stable.
• Hazardous Decomposition Products: None
• Hazardous Polymerization: will not occur.
• Incompatibility: Acids, alkalies, other toxic materials may inactivate biological cultures.
• Conditions to Avoid: Incompatible substances

• Toxicological Data:

  RTECS: Bacterial cultures: 1004274VB / CAS 116469-86-4: 1012301CS/ CAS 7732-18-5: ZC0110000

• Carcinogenicity: Ingredients not listed by ACGIH, IARC, NIOSH, NTR, or OSHA

 Environmental Fate: This product is not likely to bioconcentrate and is unlikely to create any negative environmental impact, other than a slight reduction in oxygen concentration at the site of release.

Environmental Toxicity: This formula is safe for aquatic environments.

• DOT Proper Shipping Name: Not regulated as hazardous by DOT
• DOT Hazard Class: None
• DOT Label: N/A

• TSCA: All chemical ingredients are listed on TSCA inventory, with no special reporting regulations
• CERCLA Reportable Quantity: None
• SARA TITLE III:

..................................Section 302/304 Extremely Hazardous Substances: None

..................................Section 311 Hazard Categorization: Acute, chronic

..................................Section 313 Toxic Chemicals: None

• Canadian WHMIS Classification: Class D2B
• Not subject to Proposition 65 labeling requirements

16. Other Information

Reason for Revision: Routine review and revision

Alken-Murray Corporation provides the information contained herein in good faith, in compliance with the Occupational Safety and Health Act of 1970, but makes no representation as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Alken-Murray warrants that this product is of merchantable quality. The implied warranty of fitness for a particular purpose is limited to the extent the products are used for the purpose or uses described on the product's label or in any written instructions or materials distributed to the buyer by Alken-Murray and is hereby disclaimed should buyer use the products in a manner inconsistent with this uses or purposes described therein. In no event shall Alken-Murray be liable for any consequential, exemplary, or incidental damages incurred by buyer even if it has been advised of the possibility of such damages.